Full Leg Boot Wrap (tall size) - Game Ready

£858.00 (incl. VAT)

This wrap covers the entire leg and foot (excluding the toes), from hip to ankle. Its patented technology combines active compression and deep-penetrating cold with temperature control, reducing inflammation, stimulating circulation, and relieving pain. It is the ideal tool for lower-limb recovery and rehabilitation after exercise, injury, or sports surgery. Its discreet anatomical design was developed with input from sports medicine specialists. Adjustable inseam length (approximately 84 to 94 cm).

Compatible with Med4 Elite and GRPro 2.1 control units (sold separately).

Reference : GRY_590922-03

CUSTOMER SERVICE

at your service Monday to Friday from 9:00 am to 5:00 pm

PAYMENT

100% SECURE

Description

Description

Full Leg Boot Wrap - GAME READY

The new full-leg wrap is a unique combination of active compression and cold for deep penetration with temperature control. With the aim of achieving better recovery and rehabilitation after injury or sports surgery.

This patented and proven technology helps to reduce inflammation, stimulate circulation and relieve pain. Its discreet, anatomical design is based on input from specialists and other sports medicine professionals.

Compatible with Med4 Elite ™ multimodality systems (compression, cold, heat, rapid contrast) and GRPro® 2.1 portable systems (compression, cold). Control units sold separately.

Dimensions :

Only the large size (L) is referenced

Actual shell length (adjustment range): 86-91 cm (34" - 36").
Approximate inseam length: 84-94 cm (33" - 37")

WRAP PRIMING To prevent 04 errors at the beginning of therapy with the Full Leg Boot when used with the GRPro* 2.1 Control Unit, it is important to prime (pre-fill) the Wrap before a therapy. With the GRPro* 2.1 Control Unit off, attach the Connector Hose to the Control Unit and the Wrap. Lay the Wrap open and flat next to the Control Unit (not on the body). Turn the System on and run a therapy with no compression. Pause after 45 seconds. Disconnect the Full Leg Boot from the Control Unit so water remains in the Wrap. It is now ready for use.

Pre-cooling the wrap with GRPRO* 2.1

The whole-leg boot is designed to deliver therapy to the whole leg and foot (excluding the toes). During therapy, a large amount of water is circulated through the wrap. Cooling/heating the wrap beforehand will help to deliver the best possible therapy. From time to time, the actual temperature may deviate from the target temperature. This is normal.

With water in the wrap and the water level in the controller at maximum, initiate cryotherapy without compression for 5 minutes. This will allow the temperature of the water in the wrap to equilibrate with that of the water in the GRPRO* 2.1 reservoir.

Adjusting the in-seam length

The Full Leg Boot is designed to accommodate various in-seam lengths. The Wrap comes ready to use with the standard length. If needed, you may adjust the length to be either longer or shorter by following the steps below.

To lengthen the wrap (longer in-seam)

Align the top edge of the boot with this line to extend the length of the crotch.

1- Detach the hook & loop of the boot section of the Wrap so that the entire Wrap lays flat on the floor or tabl

2- Fold the boot section over so that the top edge aligns with the lower marker (see icon at left). This will add approximately 1” to the standard in-seam length.

3- Secure the boot in place by folding the top piece of hook & loop toward you as shown.

To shorten the wrap (shorter in-seam)

Align the top edge of the boot with this line to shorten the length of the crotch.

1- Detach the Velcro fastener from the boot part of the wrap so that the whole wrap lies flat on the floor or on a table.

2- Fold the boot part so that the top edge is aligned with the top mark (see icon on the left). This shortens the standard crotch length by about 2.5 cm (1 in.).

3- Secure the boot in place by folding the top piece of hook & loop toward you as shown.

Full leg boot wrap application

Apply the Wrap with a uniformly close fit, ensuring there are no kinks which may impede water flow. Ensure the connector hose is placed to prevent the Wrap from folding or kinking at the hose inlet location of the Wrap.

NOTE: always apply the wrap while sitting or lying down with your legs straight. The full-leg boot can be applied to either the left or right leg.

1- Place the Full Leg Boot flat on the floor or on a therapy table.

2- The Full Leg Boot ships with the boot section already formed. Place the affected foot into the lower section of the boot with the heel in the designated area.

3- Fold the wrap across the top of the foot and secure on the opposite side of the foot.NOTE: Never cover the toes when applying the Full Leg Boot.

4- Fold the wrap around the ankle and secure on the opposite side of the leg.

5- Fold the loop side across the top of the leg, ensuring there are no wrinkles in the fabric and that it’s tight against the leg.

6- Fold the hook side across the top of the leg in the other direction, ensuring there are no wrinkles in the fabric and that the wrap is tight against the leg.

7- Attach the Wrap to the Control Unit with the Connector Hose. There should be an audible “click”. To disconnect, simply press the blue or gray button and remove the connector from the Wrap.

8- To remove the Wrap, unhook the leg portion first, then unhook the foot portion. Set the Wrap away from the body.

Full Leg Boot Application Video:

Game Ready Full Leg Boot Assembly Video